View MC10E193_88355.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Error Detection/Correction Circuit
The MC10E/100E193 is an error detection and correction (EDAC) circuit. Modified Hamming parity codes are generated on an 8-bit word according to the pattern shown in the logic symbol. The P5 output gives the parity of the whole word. The word parity is also provided at the PGEN pin, after Odd/Even parity control and gating with the BPAR input. This output also feeds to a 1-bit shiftable register, for use as part of a scan ring. Used in conjunction with 12-bit parity generators such as the E160, a SECDED (single error correction, double error detection) error system can be designed for a multiple of an 8-bit word.
MC10E193 MC100E193
ERROR DETECTION/ CORRECTION CIRCUIT
* * * * * *
Hamming Code Generation 8-Bit Word, Expandable Provides Parity of Whole Word Scannable Parity Register Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors
FN SUFFIX PLASTIC PACKAGE CASE 776-02
B INPUTS 03 6 574 2 1
LOGIC DIAGRAM
B2, B3, B6, B7 P2
Pinout: 28-Lead PLCC (Top View)
B1, B3, B5, B7 P1 EV/OD P3 BPAR B1, B2, B4, B7 P4 B0 VEE B1 B2 B3 0 1 EN HOLD S-IN SHIFT CLK * All VCC and VCCO pins are tied together on the die. 0 1 D PARERR PARERR 27 28 1 2 3 4 5 B4 6 B5 7 B6 8 B7 9 VCCO 10 P1 11 P2 17 16 15 14 13 12 PARERR VCC P5 VCCO P4 P3 26 EN 25 B4, B5, B6, B7 HOLD S-IN 24 23 SHIFT CLK VCCO PGEN 22 21 20 19 18 PARERR
BYTE (B0 - B7) P5
BPAR EV/OD
PGEN
7/96
(c) Motorola, Inc. 1996
2-1
REV 3
MC10E193 MC100E193
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 112 112 min typ max 150 134 134 112 112 min 25C typ max 150 134 134 112 129 min 85C typ max 150 134 155 Unit A mA Condition
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol tPLH tPHL Characteristic Propagation Delay to Output B to P1, P2, P3, P4 B to P5 EV/OD, BPAR to PGEN B to PGEN CLK to PARERR Setup Time SHIFT S-IN HOLD EN EV/OD BPAR B Hold Time SHIFT S-IN HOLD EN EV/OD BPAR B Rise/Fall Times 20 - 80% min 350 400 350 600 300 400 300 750 500 1300 1300 1700 200 300 100 100 - 200 - 200 - 300 300 typ 700 775 650 1000 550 150 50 350 250 850 850 1100 -150 - 50 - 350 - 250 - 850 - 850 -1100 700 1100 max 1000 1150 850 1450 850 min 350 400 350 600 300 400 300 750 500 1300 1300 1700 200 300 100 100 - 200 - 200 - 300 300 25C typ 700 775 650 1000 550 150 50 350 250 850 850 1100 -150 - 50 - 350 - 250 - 850 - 850 -1100 700 1100 max 1000 1150 850 1450 850 min 350 400 350 600 300 400 300 750 500 1300 1300 1700 200 300 100 100 - 200 - 200 - 300 300 85C typ 700 775 650 1000 550 150 50 350 250 850 850 1100 ps -150 - 50 - 350 - 250 - 850 - 850 -1100 ps 700 1100 max 1000 1150 850 1450 850 ps Unit ps Condition
ts
th
tr tf
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E193 MC100E193
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E193 MC100E193
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E193/D*
MC10E193/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E193

	To Download MC10E193 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .